Flame Detectors - Mounting Accessories
Tilt Mount
For: 40/40 series

The Tilt Mount is an adjustable mounting bracket to allow the detector to be oriented towards the intended fire detection area to maximize coverage.

PN 40/40-001

Outline Drawings for Tilt Mount and Tilt Mount installation.

Swivel Mounting Brackets
For: 20/20 series

The Swivel Mounting Brackets allow accurate directional selection of the detector for optimum area coverage. These brackets allow movement up to 40º in every direction thus ensuring maximum effectiveness and accurate location of the detector's coverage area. 

PN 20/20-003

Tilt Mount
For: 20/20 series

The Tilt Mounting Brackets allow accurate directional selection of the detector for optimum area coverage. These brackets movement ensure maximum effectiveness and accurate location of the detector's coverage area.

PN 20/20-005

Duct Mount
For: 40/40 series

The Duct Mount allows flame detection in areas where high temperatures exist or in cases where the detector cannot be installed inside the area. It comprises a special duct mount arrangement with specific optical window to allow installation in high temperature duct applications. The mount can be used with all Spectrex 40/40 Series flame detectors.

PN 777670
For more details, refer to manual TM777670.

Outline Drawings for Duct Mount and Duct Mount installation.

Duct Mount
For: 40/40 series

The Duct Mount is designed to allow flame detection in areas where high temperatures exist or in cases where the detector can't be installed inside the area. It comprises a special duct mount arrangement with optical window and heat sink to allow installation in high temperature duct applications. This special High Temperature mount can be used with all Spectrex 20/20 Series flame detectors.

PN 794716-2

PN 794716-3

U-Bolt / Pole Mount
For: 40/40 series

The U-bolt mount is available to facilitate either 2” or 3” pipe mounting.

Material: Stainless steel

PN 789260-1 -  Pipe 3” Version

PN 789260-2 - Pipe 2” Version

Outline Drawings for U-Bolt / Pole Mount installation.

Flame Detectors - Weather Shields
Sun Protector
For: 20/20 series

The Sun Protector is designed to protect the detector from direct extreme temperatures from the sun.

PN 780280

Weather Protector
For: 40/40 series

The Weather Protector is designed to protect the detector from rain and snow and direct extreme temperatures from the sun. 

PN 777163 Stainless steel, red epoxy

PN 777263 Plastic (ABS conductive), red

Outline Drawings for Weather Protector and Weather Protector installation - St.St. and Plastic.

Rain Cover
For: 20/20 series

The Rain Cover is designed to protect the detector from rain and snow.

PN 780981

Rain Cover
For: 40/40 series

The Rain Cover is designed to protect the detector from rain and snow.

PN 787980

Flame Detectors - Laser Aimers & Air Shields
Air Shield
For: 40/40 series

The special Air Shield, developed for SharpEye optical flame detectors, allows their installation under tough environmental conditions where they may be exposed to oil vapors, sand, dust and other particulate matter.

For more information, refer to manual TM777650.

PN 777650

Laser Aimer
For: 20/20 series

Does the optical detector cover the entire hazardous area that needs protection? Has the installer located the detector at the right location and does the detector's cone of vision cover the most dangerous spot?

These questions can be answered with the use of a simple tool -- the Laser Detection Area Coverage Pointer that designates the optical flame detector's area of coverage (cone of vision) on-site at the specific installation. This add-on acessory enables the designer and installer to optimize the detector's location and teh actual detection area coverage of each installed detector.

PN 787969

Air Shield
For: 20/20 series

The special Air Shield, developed for SharpEye optical flame detectors, allows their installation under tough environmental conditions where they may be exposed to oil vapors, sand, dust and other particulate matter.

PN 20/20-787

Cone Viewer
For: 40/40 series

Does the detector cover the area that needs protection? Is it located correctly and does the detector’s cone of vision cover the most dangerous spot? The answer - use the Cone Viewer that designates the optical flame detector’s area of coverage (cone of vision) on-site at the specific installation. This accessory enables the designer/installer to optimize detector location and its actual detection area coverage.

PN 777166

Outline Drawings for Cone Viewer and Cone Viewer installation.

Air Shield
For: 40/40 series

Optical flame detectors are often used in highly polluted or dirty areas that force maintenance personnel to access the detector frequently and clean its optical window. The special Air Shield, developed for SharpEye optical flame detectors, allows their installation under tough environmental conditions where they may be exposed to oil vapors, sand, dust and other particulate matter.

PN 780960

Laser Detection Area Coverage Pointer
For: 40/40 series

Does the optical detector cover the entire hazardous area that needs protection? Has the installer located the detector at the right location and does the detector's cone of vision cover the most dangerous spot?

These questions can be answered with the use of a simple tool -- the Laser Detection Area Coverage Pointer that designates the optical flame detector's area of coverage (cone of vision) on-site at the specific installation. This add-on acessory enables the designer and installer to optimize the detector's location and teh actual detection area coverage of each installed detector.

PN 780909 

Flame Detectors - Fire Simulators
FS Series Flame Simulator
For: 40/40, 20/20, 20/20M series

The SharpEye Series Flame Simulator is the essential complimentary tool to the self-testing capabilities of Sharpeye Flame Detectors. It brings fire prevention safety to a higher level by giving you the ability to fully test the operational readiness of your entire fire detection system:

  • Test the integrity of all the system components: all alarm outputs, all cabling and connections and the fire alarm panel functionality.
  • Test clear line of sight: By using the Spectrex Flame Simulator, you will ensure that no object is obstructing the field of view, and that the detector‘s window lens is not obscured.

Therefore, by simulating a fire that actually triggers the detector outputs, the FS Series Flame Simulators verify the correct operation of the detector, perform an essential end-to-end loop test and verify window cleanliness.

The following models are available:

  • FS-1100 - IR3 detectors. Click here for the FS-1100 datasheet.
  • FS-1200 - UV and UV/IR detectors. Click here for the FS-1200 datasheet.
  • FS-1300 - Single IR detectors. Click here for the FS-1300 datasheet.
  • FS-1400 - Multi IR detectors. Click here for the FS-1400 datasheet.
Flame Detectors - Maintenance Software & Mini Laptops
Mini Laptop Kit
For: 40/40, 20/20, 20/20M series

The mini laptop, pre-loaded with Spectrex software, enables the user to re-configure settings or perform diagnostics on all Spectrex flame and gas detectors. The kit includes cable harness with RS485/232 converter. The mini laptop is programmed with maintenance winhost for all detector types. 

For more details, refer to manual TM777070.

PN 777820

Outline Drawings for Mini Laptop Kit installation.

USB RS485 Harness
For: 20/20 series

The USB RS485 Harness Kit with RS485/232 converter, used with Spectrex Host software, enables the user to connect to any available PC or laptop to re-configure settings or perform diagnostics on all 40/40 series flame detectors. 


For more details, refer to manual TM777050.

P/N 794079-3 for 20/20SH, SI, CTIx, MI, ML

P/N 794079-5 for 40/40 Series

P/N 794079-6 for 20/20SI SIL Series

Outline Drawings for USB RS485 Harness installation.